Water Cut Meter

Water Cut Meter

Universal IV ™ CM Model with Temperature Compensation

Universal IV ™ CM Model with Temperature Compensation

Easy Configuration with Built-in Display and Keypad
All Universal IV CM comes from the factory precalibrated and requires only one point validation. Field configuration can be done from anywhere along the two-wire loop with our HRTWin PC Software. You can also configure via local display / keypad without the need for laptop or handheld communicators.
Worldwide Approvals
The Universal IV CM Model has been approved for Class I, Div1, and Zone 0 hazardous locations. FM, FMc, ATEX, as well as IECEx approvals are available.
Eliminate Routine Maintenance
The Universal IV CM ignores paraffin and other coatings that buildup on the probe. No need to take apart spool pieces and tie-off large pipelines. The Universal IV CM can be configured for NPT or flanged mountings and can be installed in common pipe diameters.
Temperature Compensation
The dielectric constant of crude oil can change with any changes in temperature. These changes may cause standard cut monitors to change without any variance in water content. The Universal IV Water Cut Monitor measures product temperature internally and calculates a true water cut reading at any temperature up to 160° F.

Additional product information below:

Universal IV ™ CM Model with Temperature Compensation

Universal IV ™ CM 2-Wire, 4-20 mA, Water Cut Monitor

Universal IV ™ CM 2-Wire, 4-20 mA, Water Cut Monitor

Easy Configuration - Now with Built-in LCD Display and Keypad
All Universal IV CM comes from the factory precalibrated and requires only one point validation. Field configuration can be done from anywhere along the two-wire loop with our HRTWin PC Software. You can also configure via local display / keypad without the need for laptop or handheld communicators.
Worldwide Approvals
The Universal IV CM Model has been approved for Class I, Div1, and Zone 0 hazardous locations. FM, FMc, ATEX, as well as IECEx approvals are available.
Durability
Our Perm-A-Seal sensing element does not require epoxy coatings that wear out and require expensive servicing. There are no gaskets that require servicing and the sensing element is robust in well fluids that include large amounts of sand.
Eliminate Routine Maintenance
The Universal IV CM (Cut Monitor) is built upon the Drexelbrook expertise in RF Admittance that allows the electronics to ignore paraffin and other coatings that buildup on the probe. No need to take apart spool pieces and tie-off large pipelines. The Universal IV CM can be configured for NPT or flanged mountings and can be installed in common pipe diameters.

Additional product information below:

Universal IV ™ CM 2-Wire, 4-20 mA, Water Cut Monitor

Universal IV ™ In-Line Water Cut Meter with Spool Piece Mounting

Universal IV ™ In-Line Water Cut Meter with Spool Piece Mounting

Easy Configuration with Built-in Display and Keypad
All Universal IV CM comes from the factory pre-calibrated and requires only one point validation. Field configuration can be done from anywhere along the two-wire loop with our HRTWin PC Software. You can also configure via local display / keypad without the need for laptop or handheld communicators.
Worldwide Approvals
The Universal IV CM Model has been approved for Class I, Div1, and Zone 0 hazardous locations. FM, FMc, ATEX, as well as IECEx approvals are available.
Eliminate Routine Maintenance
The Universal IV CM ignores paraffin and other coatings that buildup on the probe. No need to take apart the spool pieces and tie-off large pipelines. The Universal IV CM can be configured as either an insertion probe with a NPT fitting (Reference our Universal IV CM Model with Temperature compensation datasheet (UIVCMT-A)) or as a flanged mounted in-line spool probe for most common pipe diameters.
Temperature Compensation
The dielectric constant of crude oil can change with any changes in temperature. These changes may cause standard cut monitors to change without any variance in water content. The Universal IV Water Cut Monitor measures product temperature internally and calculates a true water cut reading at any temperature up to 160° F.

Additional product information below:

Universal IV ™ In-Line Water Cut Meter with Spool Piece Mounting

Comments are closed.